徐州NSK轴承61805减轻常见原因造成的损伤

减速器徐州NSK轴承的损坏是一个常见问题。除了轴承本身的质量问题外，常点减速器还列出了轴承损坏的其余原因，供您参考。

Damage of NSK bearing in Xuzhou reducer is a common problem. In addition to the quality problems of the bearing itself, the c***tant point reducer also lists the other causes of bearing damage for your reference.

1：轴承室不干净，没有油。轴承具有额定负荷高、噪音低、大大降低维护成本、延长机器运行时间等优点。例如，轴承保持架内的微小刚性材料没有彻底清洗，轴承滚道在运行中损坏，导致轴承温升过高，烧坏轴承。

1: The bearing room is not clean and there is no oil. Bearing has the advantages of high rated load, low noise, greatly reducing maintenance costs and prolonging machine operation time. For example, the tiny rigid material in the bearing cage has not been thoroughly cleaned, and the bearing raceway is damaged in operation, resulting in excessive temperature rise of the bearing and burning out the bearing.

2：由于电机本体温升过高，徐州NSK轴承补油不足，导致轴承缺油甚至烧坏。

2: Because of the excessive temperature rise of the motor body, Xuzhou NSK bearings are insufficient in oil replenishment, resulting in oil shortage or even burnout of bearings.

3：轴承装配不当，如冷负荷下轴承内圈攻丝不均，造成轴磨损，造成轴承内圈与轴承干涉损失，或减少干涉，导致内圈运转。电机端盖攻丝不均，导致轴承腔与轴承外圈配合不当，造成外圈偏移。通过触摸轴承上的钢印，可以更快、更准确地识别轴承。如果你用手触摸***，你就感觉不到了。然而，钢印的存在可以用钉子触摸。内圈或外圈是否会引起轴承的温升急剧上升和烧坏，特别是内圈的失效会导致徐州NSK轴承轴的转动。严重磨损和弯曲。然而，外环的间歇运行通常不会导致轴承温度急剧上升。只要轴承状况良好，允许外环间歇运行。

3: improper assembly of bearing, such as uneven tapping of bearing inner ring under cold load, resulting in shaft wear, resulting in interference loss between bearing inner ring and bearing, or reducing interference, leading to inner ring operation. The uneven tapping of motor end cap results in improper matching between bearing chamber and bearing outer ring, resulting in outer ring offset. By touching the steel stamp on the bearing, the bearing can be recognized more quickly and accurately. If you touch the stamp with your hand, you won't feel it. However, the existence of steel stamps can be touched by nails. Whether the inner ring or outer ring will cause the temperature rise of the bearing to rise sharply and burn out, especially the failure of the inner ring will lead to the rotation of Xuzhou NSK bearing shaft. Severe wear and bending. However, the intermittent operation of the outer ring usually does not lead to a sharp rise in bearing temperature. The outer ring is allowed to run intermittently as long as the bearing is in good condition.

4:由于定、转子铁心轴向错位或加工后转轴重新对中精度低，轴承内外圈不在切向平面内，使轴承运转无硬化，后期温升烧坏。

4: Because of the axial misalignment of stator and rotor cores or the low accuracy of re-alignment of rotating axles after processing, the inner and outer rings of bearings are not in the tangential plane, which makes the bearings run without hardening, and the later temperature rise burns out.

5：更换徐州NSK轴承后，过度干涉或椭圆电机端盖套会导致球隙过小或不均匀，导致摩擦增大，温度急剧上升，直至烧坏。

5: After the replacement of Xuzhou NSK bearing, excessive interference or elliptical motor end cover will lead to too ***all or uneven ball clearance, resulting in increased friction, temperature rise sharply until burnout.

6：轴承因混合不同类型的润滑脂而损坏。

6: Bearings are damaged by mixing different types of grease.

7：备用机器长时间不运转，油脂变质，轴承生锈，未修理。当徐州NSK轴承识别出轴承的真实性时，通过触摸轴承上的钢印，可以更快、更准确地识别轴承的真实性。如果用手触摸，***是不可触摸的，但可以用钉子触摸***。

7: Standby machine is not running for a long time, grease deterioration, bearing rust, not repaired. When Xuzhou NSK bearing recognizes the authenticity of the bearing, it can recognize the authenticity of the bearing more quickly and accurately by touching the steel seal on the bearing. Stamps are not touchable if touched by hand, but they can be touched by nails.

对于上述七种情况，您可以比较在使用过程中遇到的问题。如果是这样，立即改进延长减速器轴承的使用。

For the above seven cases, you can compare the problems encountered in the use process. If so, immediately improve the use of extended reducer bearings.

文章来自：徐州SKF轴承 www.wh-skf.com

Article from: Xuzhou SKF Bearing www.wh-skf.com

文章来自：徐州INA轴承 www.ina-china.cn

Article from: Xuzhou INA Bearing www.ina-China.cn

文章来自：徐州NSK轴承 www.klbbearings.com

Article from: Xuzhou NSK Bearing www.klbbearings.com

***：524085168

电话：0510-81207777

手机：13311666672/13395185757